DETEWE OpenCom 130 User Manual Download Page 75

Page: 75 / 204

Configuration

Configuration

Configuration and programming of the OpenCom 100 is performed by the

Confi-

gurator

, a special software application integrated into the system. The

Configu-

rator

is operated via the Web console, which can be run on any PC connected to

the OpenCom 100.

The OpenCom 100 Web console (this screenshot: OpenCom 150)

Using the Web console, you can:

■

perform the initial configuration of the OpenCom 100,

■

configure users of the OpenCom 100 and authorise them to use certain system
services,

■

carry out further system maintenance,

■

use PC-supported telephony functions,

■

read out call charge information,

■

access the OpenCom 100 telephone book.

The Web console has an integrated online help function that offers compre-
hensive information on configuration and maintenance of the OpenCom 100 (see

Loading the Online Help

starting on page 78).

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands