DETEWE OpenCom 130 User Manual Download Page 48

Page: 48 / 204

Installation

Port Assignment, Termination, Cable Lengths

In the case of the OpenCom 100, the S

buses are terminated by software. You

make this setting in the S

port configuration in the

Configurator

on the Web

console.

You can connect up to eight terminals on every internal S

bus; up to three of the

terminals can operate without an external power supply. The length of the four-
wire cable of an internal S

bus must not exceed 150 m. The power consumption

of each internal S

bus is approx. 2 W.

Ports on Interface Cards

The S

bus is terminated at one end by the OpenCom 100.

IAE = ISDN socket (German: “ISDN Anschluß Einheit”) or an ISDN terminal.
TR = terminating resistor, the S

termination. The TR must be at the termination of the

line. This can also be done by an appropriately wired IAE.

The S

bus is terminated by the TR at the ends.

Termination on an ISDN socket

OpenCom

IAE

OpenCom

IAE

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands