DETEWE OpenCom 130 User Manual Download Page 91 | Manualshive

Page: 91 / 204

background image

Configuration Examples

OpenCom 100 in a Serverless LAN

89

IP enables the establishment of connections via one or more intermediate sta-
tions. The decision whether to connect directly or indirectly to the partner device
depends on the network mask. The network mask for a class C network is
255.255.255.0. If the IP address of the partner device does not fit the network
mask, the connection is established via the default gateway. If a device knows
several data routes to different intermediate stations, one speaks of a router.

The domain name system (DNS) resolves a plain text DNS name into an IP address.
The DNS is a hierarchically structured database, distributed worldwide. A DNS
server can supply information on the names and IP addresses for which it is
responsible. For all other information, a DNS server contacts other DNS servers. For
the establishment of every connection from the workstation, it is possible to give
either an IP address, or a name that a DNS server resolves into an IP address.

Note:

For further explanations of technical terms, refer to

the Glossary on the CD supplied.

8.3

OpenCom 100 in a Serverless LAN

In a peer-to-peer network, the workstations are connected to one another via
network cables. In many networks, the cables run in the form of a star from a
central hub or switch. Such networks do not require special servers. This configu-
ration example is also valid for a LAN with a server using a protocol other than IP
(e.g. AppleTalk or IPX/SPX).

The OpenCom 100 in a serverless LAN

In a serverless LAN, the OpenCom 100 takes over the IP configuration of the con-
nected workstations. All IP settings necessary for the workstations are assigned by

OpenCom

(DHCP, RAS,

int. DNS, Internet)

S

0

Net

PC 2

Net

ISP

(DNS)

S

0

Ext.

PC

S

0

PC 1

Net

Hub

«
...
89
90
91
92
93
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Barco Pages: 2

Brand: Fagor Pages: 10

Brand: Fagor Pages: 172

Brand: Fagor Pages: 112

TVNext NN01-054

Brand: Fractus Antennas Pages: 14

Brand: CLIMAVENETA Pages: 23

magicbox aavelin

Brand: ClearOne Pages: 93

Brand: GROM Audio Pages: 16

Brand: Powrmatic Pages: 36

Brand: Jaycar Pages: 8

Brand: Hioki Pages: 32

Brand: JiangYi Pages: 13

Brand: Revo Pages: 6

Brand: Sound Freaq Pages: 19

Brand: Boss Audio Systems Pages: 20

Brand: Advanced Native Technologies Pages: 29

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands