DETEWE OpenCom 130 User Manual Download Page 172

Page: 172 / 204

Configuration Guide

Overview

170

17.1

Overview

Flowchart: Overview

Yes

Finished

Ethernet network

(LAN) exists?

Connect the OpenCom and the

configuration PC to the network

Connect the configuration

PC to the OpenCom COM port.

Generate the Dialup Networking

entry with “occonfig”.

Configure OpenCom

Least Cost Routing function?

Configure OpenCom

network functions?

Yes

Dial in (RAS)?

Connection (LAN)?

Internet?

E-mail?

Yes

Create the user groups and users.

Set the system data. Select the access type. Connect
the S

, U

and analogue devices and configure them.

Configure the call distribution scheme.

User Manager

PBX Configuration

Save data

E-Mail Configuration

WAN Configuration

Branch Configuration

RAS Configuration

LAN Configuration

LCR Configuration

Configure the Least Cost Routing
function: zones, network providers
and holidays.

Start the OpenCom configuration

service via your Web browser.

Enter the OpenCom address, for

example “http://192.168.99.254”.

Connect the configuration

PC to the OpenCom LAN port.

Enable DHCP.

Cross-connected ethernet

cable available?

Yes

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands