DETEWE OpenCom 130 User Manual Download Page 16 | Manualshive

Page: 16 / 204

background image

Features

14

DECT Data Communication

Note:

With an OpenCom 131 DECT Data Communication is

not possible because the OpenCom 131 U

pn

ports are not

DECT-enabled.

The OpenPhone 27 DECT terminals enable PCs that are not connected to the
OpenCom 100 via the internal S

0

ports or the Ethernet interface to access the

Internet. These PCs can make full use of all the Internet and e-mail features of the
OpenCom 100.

Data is transmitted via the internal data interface of the OpenPhone 27. For this
the OpenPhone 27 is connected with the serial port of the PC. The Internet can
then be accessed directly via the remote data transfer (i.e. dial-up) network. The
OpenPhone 27 sets up a data connection with the OpenCom 100 via the DECT air
interface. The remainder of the connection set-up is either direct - through an
ISDN B-channel - or indirect - through the internal RAS access of the
OpenCom 100. Indirect RAS access is preferable. This uses the routing function of
the OpenCom 100 and thus also the security features of the shared Internet
access.

For detailed information on the installation of the required driver software and the
various types of configuration, refer to the user guide for the OpenPhone 27.
For information on configuration of the OpenPhone 27 with a data interface,
please refer to the online help documentation of the OpenCom 100.

E-mail

The OpenCom 100 has an integrated e-mail function that is able to use the POP3,
APOP or IMAP4 protocols to check the Internet service provider for incoming mail.
When configuring the OpenCom 100, e-mail account query can be configured for
every member of staff. The OpenCom 100 then fetches the incoming e-mail
headers (subjects) and senders from the mail server at set intervals, and forwards
them to users’ system terminal.

E-mail accounts for the sending e-mail can also can be configured for users. E-
mails can then, for example, be sent directly from the

OpenCTI 50

to other users.

In addition, users who have had a voicebox configured for themselves, can let
themselves be notified of new voicebox messages via e-mail.

Important events and errors are kept by the OpenCom 100 in an internal log book:
the error store. To inform or alert the system administrators, entries in the log book
(system messages) can be sent via e-mail.

«
...
14
15
16
17
18
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Magnavox Pages: 23

Brand: Brähler Systems Pages: 25

Brand: Maco Pages: 40

Brand: Discount Car Stereo Pages: 6

Brand: SAL Pages: 20

Brand: AVer Pages: 107

Brand: Jensen Pages: 19

Brand: Hyundai Pages: 61

Brand: TechniSat Pages: 24

L-force CANopen EMF2178IB

Brand: Lenze Pages: 154

Brand: Kenwood Pages: 24

Brand: Kenwood Pages: 21

Brand: Kenwood Pages: 28

KMR-700U - Radio / Digital Player

Brand: Kenwood Pages: 35

Brand: Kenwood Pages: 17

Brand: Kenwood Pages: 66

KOS-A300 - CarPortal Media Controller

Brand: Kenwood Pages: 51

Brand: Kenwood Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands