DETEWE OpenCom 130 User Manual Download

Page: 58 / 204

Installation

Connectible Devices

Connection of

doorway equipment produced by Siedle

Note:

The above diagram shows the usage of the “PVG 402-

0” module (which merely serves as an example). Other mo-
dules can also be operated, such as its successor, “PVG 602-
01”.

3.12.5 COM Port

By installing the V.24 interface card a serial port on the COM interface is provided.

Please note:

The connection line for the COM port can be up to three me-
tres long.

A PC for configuring the OpenCom 100 or transmitting call data can be connected
to the COM port. This call data can be evaluated in detail with the call charge regis-
tration program OpenCount.

Door bell

Siedle

Sensor

Actor1

Actor2

a/b1

Door opener

Relay

PVG 402-0
Amplifier

-T

Ts*

NG 402-02
Ac adapter

230 V ~

12 V ~

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands