DETEWE OpenCom 130 User Manual Download

Page: 67 / 204

Connector Module

Connector Module

The S

connector module allows you to operate an OpenCom 130/150 on a

primary rate access. This access provides up to 30 voice channels. You can also use
the S

port to network two systems, e.g. in order to use the OpenCom 130/150 as

a subsidiary system or DECT server.

Note on DECT applications in conjunction with S

If an S

connector module is installed in the OpenCom 130/150, please consider

the following restriction for DECT applications:

It is not sufficient, to install a U

interface card (e.g. “4 x U

”) into slot 2 (or into

slot 3 with the OpenCom 150). In every case, you need to run a U

interface card

(“4 x U

”, “8 x U

” or “2 x S

and 6 x U

”) in slot 1 in order to operate DECT appli-

cations properly.

Note:

The maximum cable attenuation between the

OpenCom 130/150 and the other system (NT or telephone
exchange) must not exceed 6 dB. This corresponds to a
length of approx. 150 to 200 m, depending on the type of ca-
ble used.

Location of the S

port on the basic module of the OpenCom 130

RJ45

LAN

V.24

Actuator

1+2

Sensor

1+2

a/b
1+2

a/b

3+4

2+3

Sensor
3

Default setting

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands