DETEWE OpenCom 130 User Manual Download Page 100 | Manualshive

Page: 100 / 204

background image

Configuration Examples

Useful Information on Internet Access

98

■

The protocol will function without TCP/UDP port numbers, e.g. ICMP or IGMP.

The OpenCom 100 NAT has suitable processes for ensuring the functions of many
important protocols affected by these rules. These are the protocols FTP (in
“active” mode), CuSeeMe (“videoconferencing”), IRC (“chat”), ICMP errors (“trace-
route”) and ICMP echo (“ping”).

Depending on the internet telephony protocol (VoIP, SIP) the required NAT
extension (“Full Cone NAT”) or RTP-Proxy is activated on the Media Gateway Card.

Protocols which require inward-directed connection establishment can be confi-
gured in the

Net Configuration

:

Port Access

menu. For further information, refer

to the online help of this menu.

«
...
98
99
100
101
102
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Panasonic Pages: 2

Brand: Innovative Technology Pages: 14

Brand: Audiovox Pages: 2

Brand: Vivax Pages: 68

Brand: Shure Pages: 18

Brand: Bigben Pages: 64

Brand: Oase Pages: 87

OPTISOUND OPTIFORD6-V8

Brand: Vibe Pages: 4

Brand: Kenwood Pages: 27

Brand: Kenwood Pages: 12

Brand: Kenwood Pages: 2

Brand: Kenwood Pages: 24

Brand: Kenwood Pages: 59

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 52

Brand: Kenwood Pages: 56

Brand: Kenwood Pages: 52

Brand: Kenwood Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands