manualshive.com logo in svg

DETEWE OpenCom 130, User Manual

The DETEWE OpenCom 130 is a cutting-edge communication system that offers exceptional functionality and ease of use. To properly install and set up this device, you can easily access the Mounting And Commissioning Manual, available for free download on our website. This comprehensive manual will guide you through every step of the process, ensuring a seamless setup experience for your convenience.

Share
Download
background image

Installation

Installing an Expansion Set

26

3.6

Installing an Expansion Set

This chapter is addressed to customers operating an OpenCom 130 system and 
who wish to equip their infocom system with multiple interface cards for extra 
ports.

With the OpenCom 150 and OpenCom 131 infocom systems installing an 
expansion set is not necessary:

■

With the OpenCom 150, all functions reside on only one large module. For this 
reason, the installation of an expansion set is not necessary for the 
OpenCom 150.

■

The OpenCom 131 is equipped with a single slot for installing an additional 
interface card. Installing an expansion set is not necessary.

The OpenCom 130 has two separate modules offering more flexibility for 
extending the system. You can either install the expansion module when you first 
assemble the system or later as part of a system upgrade. In both cases, follow the 
mounting sequence as described here:

1.

Turn off the OpenCom 130. Unplug the plug-in power supply from the socket. 
You should not install the expansion module or install or uninstall additional 
interface cards while the OpenCom 130 is turned on.

2.

Open the housing cover of the OpenCom 130. In this case, carefully follow the 

Safety Precautions

 starting on page 23.

The existing basic module is mounted in the left half of the housing. No com-
ponents may be mounted in the right half of the housing.

3.

Place the expansion module in the intended mounting location in the right 
half of the housing. Be sure to align the 96-pin connector properly to the 
socket on the basic module. Push the expansion module towards the basic 
module so that both modules are securely connected to one another via the 
96-pin connector.

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Magnavox FW391C Instructions Manual preview
FW391C
Brand: Magnavox Pages: 26
Aastra Ascotel Office 45 Operating Instructions Manual preview
Ascotel Office 45
Brand: Aastra Pages: 40
Aastra OpenCom 100 Mounting And Commissioning User Manual preview
OpenCom 100
Brand: Aastra Pages: 244
Aastra 632d Quick User Manual preview
632d
Brand: Aastra Pages: 30
Aastra 5380 Quick User Manual preview
5380
Brand: Aastra Pages: 24
Aastra IntelliGate A150 System Manual preview
IntelliGate A150
Brand: Aastra Pages: 524
Aastra Ascotel IntelliGate 150 System Manual preview
Ascotel IntelliGate 150
Brand: Aastra Pages: 228
Aastra S850i User Manual preview
S850i
Brand: Aastra Pages: 22
Nakamichi ARIES 34 Owner'S Manual preview
ARIES 34
Brand: Nakamichi Pages: 32
Sena SF4 Quick Start Manual preview
SF4
Brand: Sena Pages: 10
Aiwa CX-NA71 Operating Instructions Manual preview
CX-NA71
Brand: Aiwa Pages: 80
Mircom FX-MNS-6000 Installation And Operation Manual preview
FX-MNS-6000
Brand: Mircom Pages: 149
VCS VideoJet 400 19" Manual preview
VideoJet 400 19"
Brand: VCS Pages: 86
Raven RCM Operation Manual preview
RCM
Brand: Raven Pages: 48
AudioBahn ABV105Q Operating Instructions Manual preview
ABV105Q
Brand: AudioBahn Pages: 11
Sanyo SHAKC64AGB Instruction Manual preview
SHAKC64AGB
Brand: Sanyo Pages: 22
ROTOTILT TLE Instructions For Use Manual preview
TLE
Brand: ROTOTILT Pages: 10
Centroid Acorn CNC Start Here preview
Acorn CNC
Brand: Centroid Pages: 2

Brands by name

Popular brands

Load more brands