DETEWE OpenCom 130 User Manual Download Page 15 | Manualshive

Page: 15 / 204

background image

Features

13

SAPI 16) can also be established between several S

0

interfaces of the

OpenCom 100. Simultaneous connections are distinguished by means of a TEI
(Terminal Endpoint Identifier).

X.31 packet data can be forwarded between two S

0

interfaces (for instance an

internal and external S

0

interface). Equally, data can be forwarded (“routed”) over

permanent QSIG lines. Data can also be routed over an S

2M

interface. It is possible

to operate multiple terminals with the same TEI on different internal S

0

interfaces.

A TEI mapping table allows these X.31 connections to be routed to the same
external S

0

interface.

The routing table for X.31 packet data is set in the Configurator under

PBX Configuration

:

X.31

. Additional information can be found in the Configu-

rator online help files.

Internet Access

It is possible to connect individual PCs to the OpenCom 100 via the internal S

0

ports, or to connect an entire LAN to the OpenCom 100 via the Ethernet port.
These PCs can access the Internet via the OpenCom 100. If Internet access is
already available from an Internet service provider, this can be configured in the
OpenCom 100. If the client network is not IP-capable, the OpenCom 100 can admi-
nister the IP configuration necessary for Internet access. The OpenCom 100 has an
integrated DHCP server and a DNS server, which in this case take over IP address
administration and name resolution for the client PCs.

The OpenCom 100 enables Internet access for all connected PCs by means of a
common IP address. Only this is externally visible. The local IP addresses of the
client PCs are translated to the IP address of the OpenCom 100 by network address
translation (NAT). In this way the client PCs in the LAN cannot be reached directly
from the Internet. This protects them from direct external attack. The LAN is additi-
onally protected by the OpenCom 100 filter lists, which can be customised indivi-
dually (firewall function).

Note:

We recommend you to read through the explanati-

ons under

Useful Information on Internet Access

starting on

page 96.

«
...
13
14
15
16
17
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Samsung Pages: 22

Brand: Jäger Pages: 50

Brand: Tait Pages: 3

Brand: Balboa Pages: 23

Brand: Yamaha Pages: 4

Brand: Yealink Pages: 6

MeetingSpace VC800

Brand: Yealink Pages: 6

Brand: Yealink Pages: 16

Brand: Yealink Pages: 4

Brand: Yealink Pages: 20

Brand: Yealink Pages: 299

VC210 Teams Edition

Brand: Yealink Pages: 12

Brand: Yealink Pages: 5

Brand: Yealink Pages: 16

Brand: Yealink Pages: 30

MeetingSpace VC200

Brand: Yealink Pages: 8

MVC Series: MVC800

Brand: Yealink Pages: 16

CP930W Telesystem

Brand: Yealink Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands