DETEWE OpenCom 130 User Manual Download Page 68

Page: 68 / 204

Connector Module

Installation

Location of the S

port on the OpenCom 150

5.1

Installation

Please note:

The module should only be installed by trained personnel.

DANGER!

The device contains hazardous voltages.

Pull out the mains plug of the OpenCom 130/150.

Open the housing of the OpenCom 130/150.

On the module board, remove the protective covers of the two S

slots (A)

and (B).

Position of the S

slots on the module board

V.24

1-2

1-1

1- 4

1-3

1-5

Slot 1

2-2

2-1

2-4

2-3

2-5

Slot 2

5-2

5-1

5-4

5-3

5-5

Slot 5

4-2

4-1

4-4

4-3

4-5

Slot 4

3-2

3-1

3-4

3-3

3-5

Slot 3

1+2

3+ 4

Actuator

1+2 Sensor 3+4

Door

1+2

LAN 1

PCM

LAN 2

Activity LED

slots

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands