DETEWE OpenCom 130 User Manual Download Page 157 | Manualshive

Page: 157 / 204

background image

Multi-Company Variant

Configuring the Multi-Company Variant

155

When setting up a new

User group

(in the

User Manager

menu), you will find

that the default company is predefined; another company can be assigned as long
as no other companies have been set up.

15.1.4 Assigning Trunk Groups/SIP Accounts

Connections of the same type and in the same direction are arranged in a trunk
group (e.g. S

0

multi-terminal connections). To be able to correctly transfer

incoming calls to the members of the configured companies (the users) via the
lines of a certain trunk group of the OpenCom 100, each of the available trunk
groups must be assigned to one of the companies. This is necessary to be able to
transfer incoming external calls to the correct company exchange in cases where
the called internal subscriber cannot be reached (“Connection to Operator”), for
example. SIP accounts can also be assigned to a company.

The assignment of trunk groups to companies is done in the

PBX Configuration:

Trunks: Bundle

menu. The assignment of trunk groups to companies is done in

the

PBX Configuration: SIP: SIP accounts

.

For outgoing external calls which users set up via the lines of their company’s
trunk group/SIP account, the assignment of the trunk group to the company is
irrelevant: the charges are assigned according to the “source” principle.

Charges are billed to the company to which the user belongs who set up the con-
nection. The OpenCom 100 recognises this on the basis of the assignment
between user groups and companies and on the basis of the routing code with
which a line of the trunk group/SIP account was seized. For more information,
please see the following section.

15.1.5 Allocating Routing Codes

Routes are used for automatic and selective seizure of trunk groups or connec-
tions for external calls. It is possible to seize a route by predialling a code.

In the

PBX Configuration: Trunks: Route

menu, you can define which company

can seize each route. An individual

code

for the seizure is allocated per route for

each company. The OpenCom 100 ensures that during configuration no seizure
code is allocated twice (for two different routes) for each company. If during confi-
guration of a route no code is allocated for one of the configured companies, the
route concerned cannot be seized by the members (user groups) of this company.

«
...
155
156
157
158
159
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: IBM Pages: 72

Brand: CAME Pages: 32

Brand: KAR-TECH Pages: 28

Brand: LENCO Pages: 27

Brand: Simplex Pages: 40

Brand: Cyrus Pages: 6

Brand: Velux Pages: 11

CIRFLEXX UMS 4100

Brand: Grundig Pages: 38

BALBOA CS6000B Series

Brand: HydroQuip Pages: 32

Brand: ALLEN & HEATH Pages: 14

Brand: Yealink Pages: 36

Brand: Scott Pages: 13

Brand: RCA Pages: 2

Brand: RCA Pages: 19

XPASS B 330/1200 L

Brand: BFT Pages: 16

Brand: AudioBahn Pages: 13

Brand: Aastra Pages: 104

Brand: TANDBERG Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands