DETEWE OpenCom 130 User Manual Download Page 135

Page: 135 / 204

PBX Networking

Configuration

133

Note:

Q.SIG-IP cannot be operated using a connection with

NAT.

12.3

Configuration

The possible configurations described below can be set up in the Web console
using the

PBX Configuration: Trunks

menu.

12.3.1 Trunk groups

This is a group of lines of the same type and direction. A line can only be assigned
to one

trunk group

(bundle).

Example of a PBX network with trunk groups

In the above example, the following trunk groups are configured for PBX 1:

■

Two S

lines in a multi-terminal configuration to the network operator which

are assigned to the “A” trunk group.

■

Two S

point-to-point connections to PBX 2 which are assigned to the “C” trunk

group.

■

One S

point-to-point connection to PBX 3 which is assigned to the “E” trunk

group.

Note:

A line or a trunk group cannot be seized directly. It is

always performed indirectly via a route.

Bundle

PBX 1

PBX 2

PBX 3

Network
operator

Trunk line

Point-to-point

connection

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands