DETEWE OpenCom 130 User Manual Download Page 70 | Manualshive

Page: 70 / 204

background image

S

2M

Connector Module

Configuration

68

On the OpenCom 150 the pressure terminal is a 5-pin connector. The addi-
tional terminal is used to connect the shielding of a shielded line. The shielding
has to be stripped as short as possible (approx. 3 mm).

6.

If necessary, check to make sure that the NT is fed by its own power supply.

7.

Reconnect the OpenCom 130/150 to the power supply.

8.

Configure the S

2M

module in the

Configurator

of the OpenCom 130/150 (refer

to

Configuration

starting on page 73).

Check the level 1 status with reference to

the LEDs on the module. None of the LEDs are illuminated before the S

2M

module has been configured.

9.

Pull out the mains plug of the OpenCom 130/150 again and close the housing.

10.

Reconnect the OpenCom 130/150 to the power supply.

5.2

Configuration

The menu item

S

2M

appears in the

Configurator

, menu

PBX Configuration: Ports

after installation of the S

2M

module. Configure the port in the input mask of this

menu item. Further information on this can be found in the online help.

LED

Meaning

1 (green)

Synchronous (= ok)

2 (green)

Blue alarm

3 (yellow)

Remote alarm or out of sync
(yellow alarm)

4 (red)

Loss of signal (red alarm)

«
...
68
69
70
71
72
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

SyncMaster VC240

Brand: Samsung Pages: 39

Brand: Samsung Pages: 91

Brand: Samsung Pages: 80

Brand: VDO Pages: 2

PSS67 IO1 16FDI

Brand: Pilz Pages: 36

Brand: S&S Northern Pages: 12

Brand: Bogen Pages: 2

Brand: PASCO Pages: 2

Brand: iRobot Pages: 7

Talk-N-Trace TM-110

Brand: JDS Uniphase Pages: 20

Brand: RCA Pages: 19

Brand: AudioBahn Pages: 14

Brand: Sanyo Pages: 16

Brand: Sanyo Pages: 20

Brand: Sanyo Pages: 28

Brand: Sanyo Pages: 32

Brand: Sanyo Pages: 43

Brand: Jensen Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands