DETEWE OpenCom 130 User Manual Download Page 11 | Manualshive

Page: 11 / 204

background image

Features

9

1.

Features

The OpenCom 100 is a communications system for integrated voice and data com-
munication. The outstanding feature of this communications system is its modular
structure:

■

The

OpenCom 131

is equipped with all the necessary ports for connecting

system telephones, ISDN devices and analogue devices. The system enables
Internet/intranet data communication, CTI applications and the system confi-
guration with a standard web browser. Additionally, the OpenCom 131 is
equipped with a slot for installing an “M100-AT” interface card. With this
interface card, the OpenCom 131 can be connected to analogue trunk lines.

■

Even with the smallest

OpenCom 130

version, it is possible to use all the most

important communications applications. The basic module enables telephony
with system telephones, ISDN telephones and analogue terminals, Internet /
intranet data communication, CTI applications, sub-system operation and
system configuration using a standard Web browser.

The expansion module of the OpenCom 130 provides three slots for further
interface cards. Using different combinations of interface cards, the configu-
ration of the OpenCom 130 can be tailored exactly to your communications
requirements. The need for additional U

pn

ports supporting DECT, further S

0

ports or more a/b ports can be met using one or more interface cards without
changing the system.

■

OpenCom 150

is a system that can be tailored exactly to your communications

requirements. Initially, the main module doesn’t carry any telephony interfaces.
They can be added by means of additional interface cards. The main module
provides five slots for different combinations of interface cards. Unlike the
OpenCom 130, the main module of the OpenCom 150 is not divided into basic
and expansion modules.

■

All named variations of the OpenCom 100 (OpenCom 130/131/150) offer addi-
tionally two special slots:

– One slot to incorporate a V.24 interface card. This card provides a serial port.

– One slot to incorporate doorstation equipment interface card.

«
...
9
10
11
12
13
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Datavideo Pages: 17

Brand: LAIA Pages: 71

Brand: RADVision Pages: 39

Brand: QNAP Pages: 35

Brand: S&S Northern Pages: 9

Brand: LOGICDATA Pages: 23

DuplicAir Intelligent Control Blue

Brand: Jydepejsen Pages: 52

Brand: Daewoo Pages: 44

Brand: Automated Logic Pages: 3

Brand: Caliber Pages: 20

Brand: Avaya Pages: 21

Brand: SoundMax Pages: 43

Brand: Wavemaster Pages: 32

Audio Everywhere

Brand: Listen Technologies Pages: 2

THOMSON DS120CD

Brand: Bigben Pages: 76

Brand: Qtx Pages: 5

DIAPERFEEDER IP54 DUOLOOP

Brand: btsr Pages: 57

Brand: Hitachi Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands