DETEWE OpenCom 130 User Manual Download Page 173

Page: 173 / 204

Configuration Guide

PBX Ports

171

17.2

PBX Ports

Flowchart: Configuring the PBX Ports

Finished

Enter the U

interfaces

and enter the internal
telephone numbers.

terminals

Analogue terminals

Sensor

COM

DECT terminals

Define the external

interfaces

Define the access type

Define the internal S

interfaces

Configure the

interfaces

Configure the DECT

terminals

Configure the
a/b interfaces

Configure the sensor

Configure the COM

interface

Yes

Do you have ISDN terminals
that you wish to operate on
an S

interface?

Do you want to operate
system telephones or
DECT terminals?

Do you want to operate
analogue terminals
(e.g. a fax machine)?

Do you want to use a
sensor contact on the
OpenCom (e.g. for a
door opener)?

Do you want to run the
OpenCount program?

Set the external S

interfaces and

enter the telephone numbers
assigned by your network provider.

Set the access type (multiterminal
access and/or system access).

Set the internal S

interfaces

and enter the internal
telephone numbers.

Do you want to operate
DECT terminals on the
OpenCom?

Check in the DECT terminals
and enter the internal
telephone numbers.

Set the analogue interfaces
and enter the internal
telephone numbers.

Enter the internal telephone
numbers for the time groups
of the sensor.

Select the “connection
data” option.

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands