DETEWE OpenCom 130 User Manual Download Page 178

Page: 178 / 204

Configuration Guide

E-mail Function

176

17.7

E-mail Function

Flowchart: Configuring the E-mail Function

LAN

Internet

LAN

Notification

Users

Finished

No e-mail use

Yes

Finished

NET Configuration:

LAN

NET Configuration:

WAN

User Manager:

Users, User Groups
and User Accounts

NET Configuration:

E-Mail Access

Have you made the network
settings for the OpenCom?

Do you want to use e-mail
from the Internet?

Has an internal e-mail server
been configured in your LAN?

Do you want to be notified of
e-mails on your system telephones?

Have you stored the
users to be notified?

Set the polling time periods.

Configure the network settings
for the OpenCom.

Configure your Internet access.

Create the users and activate
e-mail notification. Also enter
the users' e-mail addresses.

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands