manualshive.com logo in svg

DETEWE OpenCom 130, User Manual

The DETEWE OpenCom 130 is a cutting-edge communication system that offers exceptional functionality and ease of use. To properly install and set up this device, you can easily access the Mounting And Commissioning Manual, available for free download on our website. This comprehensive manual will guide you through every step of the process, ensuring a seamless setup experience for your convenience.

Share
Download
background image

Configuration

Brief Guide to Initial Configuration

74

Note:

In order to use all the new system software functions, 

we recommend that you download the latest software from 
our Web site at http://www.aastra-detewe.de.

For the initial configuration you can connect the PC to the OpenCom 100 via the 
Ethernet port. A COM port can also be used. The TCP/IP network protocol is used 
to set up a connection via one of these ports. You can then open the Web console 
of the OpenCom 100 and call up the 

Configurator

 from there.

Note:

To avoid problems with existing network installations, 

the OpenCom 100’s DHCP server is designed for static 
address assignment in its factory settings. The 
OpenCom 100’s IP address is always168.99.254 in its factory 
settings.

7.1

Brief Guide to Initial Configuration

Setting up a first connection is quite simple with a standard Windows PC:

1.

Connect the PC’s network card with one of the OpenCom 100.’s LAN ports Use 
a cross-wired Ethernet cable to do this. You can also use an uncrossed Ethernet 
cable for a connection via a LAN port to the OpenCom 130’s expansion 
module. 

2.

Windows 2000/XP: log on as a user with “Administrator” rights.

3.

You will find the IP settings in Windows 2000/XP under 

Start

: 

Settings

: 

Network connections

: 

Local Area Connection

. Open the dialogue box 

Local 

Area Connection Properties

, and then the dialogue box 

Internet Protocol 

TC/IP Properties

 (see figure: 

Setting the IP address in Windows XP

 on page 75).

4.

Note down the existing settings so that you can restore them after completing 
the initial configuration.

5.

Change the 

IP Address

 to 192.168.99.253. Change the 

subnet mask

 to 

255.255.255.0, confirm with 

OK

 and 

Close

.

6.

Start a Web browser and in the address field enter “http://192.168.99.254/”.

The Web console’s log-on page will be displayed. Enter the user name “Administ-
rator” without a password for the initial configuration. To support your next confi-

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Badger Meter MDS 2000 Installation And Software Manual preview
MDS 2000
Brand: Badger Meter Pages: 48
Data I/O PSV5000 Operator'S Manual preview
PSV5000
Brand: Data I/O Pages: 88
M&S Systems dmc1 Finish-Out Rough-In Instructions preview
dmc1 Finish-Out
Brand: M&S Systems Pages: 8
texet TR-3003 User Manual preview
TR-3003
Brand: texet Pages: 28
Jensen Mobile Multimedia AM/FM/DVD Receiver VM9311 Instruction Manual preview
Mobile Multimedia AM/FM/DVD Receiver VM9311
Brand: Jensen Pages: 90
EIS kb sound Series Installation Manual preview
kb sound Series
Brand: EIS Pages: 2
Watts Vision BT-A02 RF Description And Application Manual preview
Vision BT-A02 RF
Brand: Watts Pages: 19
Parker 2003-CB-00 Technical Manual preview
2003-CB-00
Brand: Parker Pages: 47
Edis 020017-1 User Manual preview
020017-1
Brand: Edis Pages: 39
Close Talk Close Talk Conference System Installation Instructions preview
Close Talk Conference System
Brand: Close Talk Pages: 2
Nortel Meridian Norstar User Manual preview
Meridian Norstar
Brand: Nortel Pages: 18
Boss Audio Systems CAP2C User Manual preview
CAP2C
Brand: Boss Audio Systems Pages: 2
Curtis RCD794R Specification Sheet preview
RCD794R
Brand: Curtis Pages: 1
SRT 306 Quick Start Manual preview
306
Brand: SRT Pages: 2
Pioneer Super Tuner III DEH-P7400MP Installation Manual preview
Super Tuner III DEH-P7400MP
Brand: Pioneer Pages: 6
Pioneer SUPER TUNER III D FH-P8000BT Installation Manual preview
SUPER TUNER III D FH-P8000BT
Brand: Pioneer Pages: 7
Pioneer Super Tuner III D+ DEH-P7750MP Service Manual preview
Super Tuner III D+ DEH-P7750MP
Brand: Pioneer Pages: 20
Pioneer Super Tuner III D DEH-P2550 Installation Manual preview
Super Tuner III D DEH-P2550
Brand: Pioneer Pages: 6

Brands by name

Popular brands

Load more brands