DETEWE OpenCom 130 User Manual Download Page 72

Page: 72 / 204

Mounting the OpenCom 150 Rack InfoCom System

Technical Data

6.2

Technical Data

(only if different from the OpenCom 150)

Dimensions:

– Width: 19-inch panel with
flange
for mounting in installation
cabinet
–Height: 3U
– Depth: approx. 340 mm

Weight:

approx. 7.8 kg

Connection of 230 VAC power supply on rear side via inlet connector for non-
heating apparatus

Connection of all ports via RJ 45 jacks on front panel

Note:

The ISDN S

ports on the front panel may only be

switched in one direction (internal or external). Use of the ex-
ternal port with a crossover (Rx-Tx) patch cable in parallel to
the S

internal port (for two S

terminals on the same bus)

may severely limit the range of the S

bus.

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands