manualshive.com logo in svg

DETEWE OpenCom 130, User Manual

The DETEWE OpenCom 130 is a cutting-edge communication system that offers exceptional functionality and ease of use. To properly install and set up this device, you can easily access the Mounting And Commissioning Manual, available for free download on our website. This comprehensive manual will guide you through every step of the process, ensuring a seamless setup experience for your convenience.

Share
Download
background image

Installation

Connectible Devices

55

Intercom System (for a/b)

The intercom systems “DoorLine T01/02” and “DoorLine T03/04” of the german 
Telekom’s division T-Com can be connected via the “DoorLine M06” to any a/b 
port. The “DoorLine” module provides the actor for the door opener contact.

Observe the following when connecting:

■

The intercom system and the “DoorLine” module should be set to their factory 
settings.

■

In the 

PBX Configuration

: 

Ports

: 

a/b

: 

Change 

menu in the Configurator, select 

Doorstation 2-wire 

under

 Type

. Activate the 

Actuator

 option, if you want to 

use the actor port of the OpenCom 100 instead of the “DoorLine” relay. The 
“DoorLine” actor can be operated only when the speech channel is open at the 
same time. The internal actor can be operated at any time.

■

The “DoorLine” intercom system has a number of bell keys to which you can 
assign different call numbers in the 

PBX Configuration

: 

Ports

: 

Doorbell

 menu 

in the Configurator.

■

You can call the “DoorLine” intercom system by entering the code procedure 

*102

.

■

The “DoorLine” intercom system can be connected to any a/b port. However, 
you can use only one “DoorLine” with the OpenCom 100. 

For details on installing and configuring the “DoorLine” intercom system, refer to 
the product user guide.

The intercom system should be installed by qualified personnel only as sensor/
actor contacts will need to be connected to the “DoorLine” module.

3.12.4 Actor/Sensor Ports

For the assignment of the ports, refer to the section 

Available Ports

 starting on 

page 34. The OpenCom 100 also functions together with a Freehand Entry-Phone 
manufactured by Siedle or Behnke.

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Barco CX-20 Quick Setup Manual preview
CX-20
Brand: Barco Pages: 4
Panamax M4000-PRO Instructions Manual preview
M4000-PRO
Brand: Panamax Pages: 16
WAREMA LONMSE 2M230I Operating And Installation Instructions preview
LONMSE 2M230I
Brand: WAREMA Pages: 4
Radionics D9000 Series Installation And Troubleshooting Quick Reference preview
D9000 Series
Brand: Radionics Pages: 14
Magnavox FW650C/22 User Manual preview
FW650C/22
Brand: Magnavox Pages: 24
iTrak BT9682GB Instruction Manual preview
BT9682GB
Brand: iTrak Pages: 6
Valcom Syn-Apps VIP-801A-SA Quick Manual preview
Syn-Apps VIP-801A-SA
Brand: Valcom Pages: 2
ITC TS-0690 User Manual preview
TS-0690
Brand: ITC Pages: 15
SEW-Eurodrive IPOS plus Manual preview
IPOS plus
Brand: SEW-Eurodrive Pages: 384
LAIA CUTE 12X User Manual preview
CUTE 12X
Brand: LAIA Pages: 9
ISOUND ISOUND-5378 User Manual preview
ISOUND-5378
Brand: ISOUND Pages: 28
TANDBERG F1 D13353.02 User Manual preview
F1 D13353.02
Brand: TANDBERG Pages: 172
Panasonic SC-MAX8700 Owner'S Manual preview
SC-MAX8700
Brand: Panasonic Pages: 64
Panasonic SC-PM700 Owner'S Manual preview
SC-PM700
Brand: Panasonic Pages: 31
Panasonic SG-D16 Service Manual preview
SG-D16
Brand: Panasonic Pages: 22
Panasonic SG-1800 Service Manual preview
SG-1800
Brand: Panasonic Pages: 27
Panasonic SG-165 Service Manual preview
SG-165
Brand: Panasonic Pages: 33
Panasonic SG-1030L Service Manual preview
SG-1030L
Brand: Panasonic Pages: 15

Brands by name

Popular brands

Load more brands