DETEWE OpenCom 130 User Manual Download Page 54

Page: 54 / 204

Installation

Connectible Devices

Example of port assignment of the OpenCom 130 with terminals

3.12.1 Internal/External S

Ports

All S

ports can be operated externally, i.e. on an ISDN network termination unit.

The S

2 port of an OpenCom 130 and an OpenCom 131 can also be connected

internally. S

ports on interface cards (available for an OpenCom 130 and

OpenCom 150) can also be switched external/internal. It is not possible to use
both assignments simultaneously.

Up to eight devices per bus (ISDN telephones, ISDN fax machines, ISDN base sta-
tions, ISDN cordless telephones, ISDN adapters for the PC among others) can be
connected to the internal S

ports by twin-pair cables. The power for three of

these devices can be supplied by the bus; if more devices are used, they then
require their own power supplies. The internal S

buses enable point-to-multi-

point calls as per the DSS1 protocol (Euro-ISDN).

3/4

a/b
1/2

a/b
3/4

Sensor 1

LAN

1 ext

NTBA

Hub

COM

1/2

2 int

Intercom/Relay

Intercom/Door opener

Actuator
1 + 2

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands