DETEWE OpenCom 130 User Manual Download Page 25 | Manualshive

Page: 25 / 204

background image

Installation

Safety Precautions

23

3.2

Safety Precautions

The CE symbol on the product confirms that it meets the technical guidelines on
user safety and electromagnetic compatibility valid at the time of approval.

Please note:

Installation and maintenance should only be performed by
specially trained personnel. Always remove the power plug
and the plug-in power supply from the mains socket before
connecting devices to the OpenCom 100 ports.

DANGER!

This device contains hazardous voltages. To make the sys-
tem powerless, remove the power plug and the plug-in
power supply from the socket.

The OpenCom 100 may only be plugged into mains sockets with a protective
earth conductor. Mount the OpenCom 100 only close to easily accessible sockets.

Only use the original plug-in power supply: No. 4512699 (TR25240-E-01A13 type)
for an OpenCom 131 and for the basic module of an OpenCom 130.

The housing cover may only be opened by authorised personnel. Unauthorised
opening of the housing cover and improper repair may damage the
OpenCom 100 and invalidate the warrantee.

CAUTIONT!

Static charges can damage the OpenCom 100. Make sure you
discharge yourself and your tools before and while installing
electrical and electronic components of the OpenCom 100.

Only devices that deliver safety extra-low voltage (SELV) may be connected to the
OpenCom 100. Proper use of authorised devices meets this requirement.

Only devices meeting the technical requirements may be connected to the ana-
logue ports. For details, refer to the section entitled

a/b Ports

starting on page 48.

«
...
23
24
25
26
27
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Safeline Pages: 8

COMPETITION ProZ4-80

Brand: µ-Dimension Pages: 7

Brand: PURE Pages: 88

Brand: WAGO Pages: 46

Brand: JAMO Pages: 72

Brand: Planet Pages: 51

Brand: SPINOGY Pages: 27

Brand: Vivax Pages: 68

Brand: Allmatic Pages: 32

Brand: LAIA Pages: 9

Brand: Juna Pages: 5

Brand: RCA Pages: 68

Brand: Vicon Pages: 91

Brand: Raven Pages: 48

Brand: Kenwood Pages: 40

Brand: Kenwood Pages: 43

Brand: Kenwood Pages: 26

Brand: Kenwood Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands