DETEWE OpenCom 130 User Manual Download | Manualshive

Page: 127 / 204

background image

PBX Cascading

Putting a Cascaded PBX into Operation

125

11.3.1 Notes

Observe the following when operating a cascaded PBX system:

■

All U

pn

, S

0

and a/b ports of the slave system can be used with appropriate tele-

phones. All features of system telephones on U

pn

ports are available without

restriction.

■

The S

0

ports of the slave system can also be used for trunk lines or for PBX net-

working (see

PBX Networking

starting on page 127).

■

It is not possible to operate a DECT base station on one of the U

pn

ports of the

slave system.

■

The COM, actor/sensor and LAN ports of the slave system cannot be used. The
LAN ports on the add-on module of slave system can be used without rest-
riction.

■

The two communications systems must have a direct Ethernet connection or
be connected via a hub in order to exchange data. They cannot be connected
through a router.

■

The OpenCom 150 is equipped with the PCM2 port in order to realize cas-
cading of a third PBX with a future release. Use one of the two LAN0 ports, to
connect the OpenCom 150 to the Local Area Network.

■

The slave system cannot be addressed directly through a LAN. For configu-
ration, always use the Web console of the master system.

■

A memory card installed in the slave system (OpenVoice, OpenAttendant)
cannot be used.

■

To operate the slave system again normally, you must reset it to its factory set-
tings (refer to

Resetting the System Data

starting on page 84).

«
...
125
126
127
128
129
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Rain Bird Pages: 48

Brand: Nacon Pages: 12

Brand: HAMTRONICS Pages: 8

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

FINISH-OUT MC111M

Brand: M&S Systems Pages: 2

Brand: Reliance Foundry Pages: 3

Brand: Omnitronic Pages: 19

Brand: Daewoo Pages: 35

Brand: Autotrol Pages: 8

Brand: MPMan Pages: 32

Brand: Daewoo Pages: 44

Brand: Automated Logic Pages: 3

Brand: Micronix Pages: 16

Brand: Panasonic Pages: 24

Brand: 3M Pages: 90

Brand: Paso Pages: 8

Brand: CDK ELECTRONICS Pages: 22

ARMT.665230.202-01

Brand: ARMTEL Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands