DETEWE OpenCom 130 User Manual Download Page 35 | Manualshive

Page: 35 / 204

background image

Installation

Installing Interface Cards

33

CAUTIONT!

Static charges can damage electronic components. Pay atten-
tion to the regulations regarding the handling of electrostati-
cally sensitive components.

3.

Carefully insert the interface card in the slot provided. The component side
must face to the right.

Ensure the plug-in connection is sitting securely.

4.

Connect the required port cable to the corresponding pressure terminals of
the relevant pressure terminal group (see also

Positions of the Ports

starting on

page 37).

5.

Close the housing cover and turn on the OpenCom 100 again.

The software of the OpenCom 100 can detect the type of interface card present.
The interface card must still be configured individually for commissioning.

You can query the status of the interface cards in the Web console when the
OpenCom 100 is operational again. To do this, call up the

PBX Configuration:

Ports: Slots

menu page. The

Status

column of the table displays a green tick

beside the slot name (for an OpenCom 130 e.g.

0/1

,

0/2

and

0/3

). The column of

the table must list the correct type of interface card.

«
...
33
34
35
36
37
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Yealink Pages: 8

Brand: Medion Pages: 308

Brand: CAME Pages: 128

Brand: Parker Pages: 47

Brand: Kicker Pages: 9

Brand: Lutron Electronics Pages: 36

Brand: DIS Pages: 54

Brand: Woodward Pages: 32

Brand: Toa Pages: 9

Brand: Paso Pages: 8

Brand: Emerson Pages: 16

Brand: Emerson Pages: 2

Brand: Emerson Pages: 8

Brand: Emerson Pages: 28

Brand: Emerson Pages: 36

Brand: Emerson Pages: 14

Brand: Emerson Pages: 31

Brand: Emerson Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands