Oracle X5-4 Скачать руководство пользователя страница 59

Страница: 59 / 358

Attaching Devices to the Server

Diagnostic

Tool

Information

Location

U-Boot

diagnostics

Oracle x86 Servers Diagnostics Guide

http://www.oracle.com/goto/
x86AdminDiag/docs

System

indicators and

sensors

Oracle Server X5-4 Service Manual

“Troubleshooting Using the Front Panel

Indicators” on page 40

POST

BIOS Setup Utility information

“BIOS Setup Utility Menu

Options” on page 273

POST

Power On Self-Test (POST) codes

“POST and Checkpoint

Codes” on page 341

UEFI

diagnostics

Oracle x86 Servers Diagnostics Guide

http://www.oracle.com/goto/
x86AdminDiag/docs

Oracle VTS

Oracle VTS software and documentation

http://docs.oracle.com/cd/E19719-01/
index.html

Attaching Devices to the Server

This section describes server port information and provides procedures for attaching devices to

the server.

■

“Attach Devices to the Server” on page 59

■

“Back Panel Connector Locations” on page 60

■

“Configuring Serial Management Port Ownership” on page 61

■

“Four Onboard 10GbE Ports” on page 32

Attach Devices to the Server

This section provides information about connecting devices to server (remotely and locally), so

you can interact with the service processor (SP) and the server console.

Connect an Ethernet cable to the Gigabit Ethernet (NET) connectors.

See

“Back Panel Connector Locations” on page 60

To connect to Oracle ILOM over the network, connect an Ethernet cable to the

Ethernet port labeled NET MGT.

See

“Back Panel Connector Locations” on page 60

Troubleshooting and Diagnostics

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды