manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Oracle X5-4 - мощный сервер для вашего бизнеса. Получите начальное руководство по эксплуатации бесплатно, скачав его с manualshive.com. Этот manual поможет вам быстро начать использовать функционал сервера и сделать ваш бизнес еще более эффективным. Начните прямо сейчас!

Поделиться
Скачать
background image

Replace the Power Supply Backplane Board (FRU)

See 

“Remove a PCIe Card” on page 161

.

Make a note of where each PCIe card installed so they can be put back in the same slots. The

internal SAS/SATA cables and NVMe cables do not need to be removed, but must be out of the

way as the motherboard needs to be removed.

5.

If the server has only two CPUs, remove the air baffle.

The air baffle simply lifts straight up and out of the system. It is not attached to anything.

6.

Remove all memory riser cards.

See 

“Remove a Memory Riser Card” on page 145

.

7.

Disconnect the fan board power and data cables from motherboard.

These cables do not need to be removed from the system and can remain plugged into the fan

board. However, care must be taken not to damage these cables when removing or inserting the

motherboard.

8.

To disconnect the power supplies from the backplane connectors, remove or

pull both power supplies at least part way out of the chassis.

See 

“Remove a Power Supply” on page 137

.

9.

Move the air divider.

The air divider separates the disk drive backplane area from the rest of the chassis and includes

the system Fault Remind button mechanism. It must be moved to allow access to the power

supply backplane board and allow removal of the motherboard. The air divider is mounted to

the power supply side wall using two tabs that are inserted into slots in the side wall. For this

procedure, you can leave the cables attached to the air divider.

Servicing FRU Components

227

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X5-4

IBM BladeCenter S Installation And User Manual preview
BladeCenter S
Бренд: IBM Страницы: 84
IBM 9008-22L Manual preview
9008-22L
Бренд: IBM Страницы: 110
IBM eserver xSeries 440 Quick Reference preview
eserver xSeries 440
Бренд: IBM Страницы: 34
IBM AMD Opteron LS20 Type 8850 Installation And User Manual preview
AMD Opteron LS20 Type 8850
Бренд: IBM Страницы: 68
B&B ES1AWB Instruction Manual preview
ES1AWB
Бренд: B&B Страницы: 55
Oase WECS II 2048/DMX/02 Operating Instructions Manual preview
WECS II 2048/DMX/02
Бренд: Oase Страницы: 67
IBM P 615 series Service Manual preview
P 615 series
Бренд: IBM Страницы: 491
Supero SUPERSERVER 5017C-MF User Manual preview
SUPERSERVER 5017C-MF
Бренд: Supero Страницы: 96
IOGear GMFPSU01 User Manual preview
GMFPSU01
Бренд: IOGear Страницы: 44
NEC Express 320Ma Read Me First preview
Express 320Ma
Бренд: NEC Страницы: 10
IBM Netfinity 4500R Installation Manual preview
Netfinity 4500R
Бренд: IBM Страницы: 60
Fujitsu PRIMERGY TX2540 M1 Operating Manual preview
PRIMERGY TX2540 M1
Бренд: Fujitsu Страницы: 92
Fujitsu PRIMERGY TX200 S5 Operating Manual preview
PRIMERGY TX200 S5
Бренд: Fujitsu Страницы: 114
Fujitsu PRIMERGY TX300 S5 Options Manual preview
PRIMERGY TX300 S5
Бренд: Fujitsu Страницы: 142
Fujitsu PRIMERGY TX200 S6 Operating Manual preview
PRIMERGY TX200 S6
Бренд: Fujitsu Страницы: 126
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual preview
Server PRIMERGY TX1330 M1
Бренд: Fujitsu Страницы: 336
Fujitsu PRIMERGY TX300 S6 Options Manual preview
PRIMERGY TX300 S6
Бренд: Fujitsu Страницы: 122
Fujitsu SE300 Operating Manual preview
SE300
Бренд: Fujitsu Страницы: 86

Бренды по названию

Популярные бренды

Загрузить еще бренды