manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 150

Install a DIMM

Install a DIMM

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Use this procedure to install a DIMM into a slot on a memory riser (MR) card.

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

■

For DIMM designation information, see 

“Component Designations” on page 73

.

■

For reference information, see 

“Memory Riser Card and DIMM Reference” on page 154

.

1.

Ensure that the DIMM ejector levers at both ends of the DIMM slot are in their

fully open position.

2.

Align the DIMM with the empty slot.

Align the notch on the DIMM with the protrusion on the DIMM slot to ensure that the DIMM is

installed correctly.

3.

Gently and evenly push the DIMM into the slot until the ejector levers rise and

lock the DIMM into place.

150

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды