Oracle X5-4 Скачать руководство пользователя страница 220

Страница: 220 / 358

Replace the NVMe Switch Card Cables (FRU)

Caution -

Hardware damage. Try not to allow the SAS and NVMe (if installed) cables to rub

against the CPU0 heatsink radiator fins. They are sharp and can damage the cable insulation.

To install the replacement cables, carefully thread the NVMe Switch card end of

the cables through the narrow space between the P0 heat sink and the power

supply cage.

Reconnect the NVMe cables to the NVMe Switch card.

If needed, reinstall the NVMe Switch card in PCIe slot 1 if you removed it earlier.

Note -

The NVMe Switch card only works in PCIe slot 1.

Reroute the NVMe cables through the air divider to the disk backplane area.

Refer to the figure in step 5 for cable routing.

10.

Reconnect the NVMe cables to their connectors on the disk backplane.

220

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды