Oracle X5-4 Скачать руководство пользователя страница 29

Страница: 29 / 358

Server Subsystems Overview

Note -

During an initial Power up sequence, the front fans will briefly run at full speed as part

of a power-on test.

Standby Power Mode

Standby power is a non-operating mode (OS does not boot), in which low-level power is

supplied only to the components that are required to run the SP. To enter standby power mode,

connect the AC power cables to the back of the server, but do not press the front panel Power

button. You can also enter standby power mode by powering off the server from full power

mode using one of the power-off methods (see below).

In standby power mode, the green SP indicator blinks while the SP is booting. Once the

SP has booted, this SP indicator is steady on, and the green System OK indicator goes to

standby blink (once every 3 seconds). See

“Server Boot Process and Normal Operating State

Indicators” on page 41

Graceful Shutdown

A graceful shutdown (also referred to as an orderly shutdown) is the safest method of shutting

down the server to standby power mode because it warns users, closes files, and prepares the

file system. To perform a graceful shutdown, use the server OS, Oracle ILOM, or the server

front panel Power button.

A Graceful shutdown via the Power button is done with a single (momentary) press. However,

an Immediate (Emergency) shutdown via the power button is done by pressing and holding the

power button for > 5 seconds.

Immediate Shutdown

An immediate shutdown of the server (also referred to as an emergency shutdown) should be

used only in situations when you know that the loss of data is nonexistent or acceptable. An

immediate shutdown does not warn users, does not properly close files, and does not gracefully

shut down the operating system. Full power is immediately removed and the server goes to

standby power mode.

Complete Power Removal

Shutting down the server from full power mode to standby power mode does

not

completely

remove power from the server. When it is in standby power mode, the server is in a low-power

state. This low-power state is enough to maintain the service processor (SP), which runs Oracle

ILOM. To completely remove power from the server, you need to remove the AC power cords.

Warm Reset or Reboot

A warm reset is a reboot or restart of the server that occurs when you cycle server power from

full power mode to standby power mode and back to full power mode. For example, a warm

Oracle Server X5-4 Overview

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды