Oracle X5-4 Скачать руководство пользователя страница 109

Страница: 109 / 358

Turn On the Locator Indicator Remotely (Oracle ILOM Web Interface)

Turn On the Locator Indicator Remotely (Oracle

ILOM Web Interface)

The Locator indicator helps you identify the a specific server in a rack.

Log in to the Oracle ILOM web interface.

To log in, open a web browser and direct it using the IP address of the server SP. Log in as root

or a user with administrator privileges. For more information, refer to the

Oracle X5 Series

Servers Administration Guide

http://www.oracle.com/goto/x86AdminDiag/docs

The Summary screen appears.

In the Actions section, verify that the Locator indicator is off, and then click the

Turn On button.

Click OK.

Preparing to Service the Server

109

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды