Oracle X5-4 Скачать руководство пользователя страница 161

Страница: 161 / 358

Remove a PCIe Card

Remove a PCIe Card

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Caution -

Component damage. Ensure that all power is removed from the server before

removing or installing expansion cards. You must disconnect the power cables before

performing this procedure.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

For PCIe slot designation information, see

“Component Designations” on page 73

Prepare for service.

See

“Prepare the Server for Cold Service” on page 94

Locate the PCIe card that you want to remove.

See

“Server Back Panel Features” on page 18

for information about PCIe slots and their

locations.

If are replacing a PCIe card with a card of the same type, make a note of where

the PCIe card is installed.

A list of supported PCIe cards and their population order is listed in the

Product Notes

for the

server.

Unplug all data cables from the PCIe card.

Make note of the cables, so you can install them in the same connectors on the replacement

card.

Servicing CRU Components

161

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды