Oracle X5-4 Скачать руководство пользователя страница 263

Страница: 263 / 358

(Optional) Install the Server Into the Rack

Push the slide-rails as far as possible into the slide-rail assemblies that are

mounted in the rack.

Raise the server so that the ends of the mounting brackets are aligned with the

slide-rail assemblies that are mounted in the rack.

Ensure that both the top and bottom mounting lips of the mounting brackets are

aligned with the slide-rails.

Caution -

Physical or component damage. The server might fall if the mounting brackets are

not inserted properly into the slide rails. Ensure that the mounting lips are properly aligned, and

then insert the brackets into the slide rails properly.

Insert the mounting brackets into the slide-rails and push the server into the

rack until the mounting brackets encounter the slide-rail stops (approximately

12 inches, or 30 cm) and the server rails lock the server into the maintenance

position.

Returning the Server to Operation

263

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды