Oracle X5-4 Скачать руководство пользователя страница 100

Страница: 100 / 358

(Optional) Remove the Server from the Rack

Caution -

Physical or component damage. The server is heavy and cannot be safely removed

from the rack by a single person. Use two or more personnel and a mechanical lift to remove

the server from the rack.

Prepare the server for service.

See

“Prepare the Server for Cold Service” on page 94

Ensure that the server is in the maintenance position.

Set up an ESD-safe service location.

Caution -

Component ESD damage. Circuit boards and hard drives contain electronic

components that are extremely sensitive to static electricity. Do not touch or handle components

unless you are wearing a properly grounded anti-static wrist strap.

See

“Performing Electrostatic Discharge and Static Prevention Measures” on page 79

Pull the mounting release brackets [1] toward the front of the server.

100

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды