Oracle X5-4 Скачать руководство пользователя страница 144

Страница: 144 / 358

Replace a Faulty Memory Riser Card

Install the MR card.

See

“Install a Memory Riser Card” on page 152

Prepare the server for operation.

See

“Prepare the Server for Operation” on page 259

Replace a Faulty Memory Riser Card

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

For memory riser card designation information, see

“Component Designations” on page 73

■

For reference information, see

“Memory Riser Card and DIMM Reference” on page 154

Identify the faulty MR card.

See

“Locate a Failed Memory Riser Card, DIMM, or CPU” on page 86

Remove the MR card.

See

“Remove a Memory Riser Card” on page 145

Set the faulty card next to the replacement card on an ESD-safe work space.

Tip -

Position the cards in the same orientation. This makes it easier to transfer the DIMMs.

Make note of the DIMM population configuration on the faulty card.

You must replicate this same DIMM population configuration on the replacement card.

The slots are color coded. For more information, see

“Memory Riser Card and DIMM

Reference” on page 154

144

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды