Oracle X5-4 Скачать руководство пользователя страница 70

Страница: 70 / 358

Component Serviceability, Locations, and Designations

Component Serviceability

The replaceable components in your server are designated as either a customer-replaceable unit

(CRU) or a field-replaceable unit (FRU).

■

A part designated as a FRU must be replaced by an Oracle-qualified service technician.

■

A part designated as a CRU can be replaced by a person who is not an Oracle-qualified

service technician.

If the component can be serviced while the server is powered on, it is called a hot-service

component. If the server has to be powered off before the component can be serviced, it is

called a cold-service component.

The following table lists the components, their service designations, and their serviceability.

Component

Service Designation

Serviceability

Storage drives

CRU

Hot

Fan modules

CRU

Hot

Power supplies

CRU

Hot

Memory risers and DIMMs

CRU

Cold

PCIe cards

CRU

Cold

DVD drive

CRU

Cold

System (or RTC) battery

CRU

Cold

CPUs and heatsinks

FRU

Cold

SAS 12 Gb/s HBA and cables (HBA-to-disk backplane)

FRU

Cold

PCIe NVMe Switch card and cables (card-to-disk backplane)

FRU

Cold

Energy Storage Module (ESM) and cable (HBA-to-ESM)

FRU

Cold

Fan board

FRU

Cold

Power supply backplane

FRU

Cold

Storage drive backplane

FRU

Cold

SP card

FRU

Cold

Motherboard

FRU

Cold

Location of Replaceable Components

The following illustrations show the Oracle Server X5-4 components:

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды