Oracle X5-4 Скачать руководство пользователя страница 18

Страница: 18 / 358

External Components and Features

Callout

Description

Locator LED/button: white

Service Action Required indicator: amber

System OK indicator: green

Power button

SP OK indicator: green

Service Action Required indicators (3) for fan module (FAN), Processor (CPU) and Memory:

amber

Power Supply (PS) Fault (Service Action Required) indicator: amber

Over Temperature Warning indicator: amber

USB 2.0 connectors (2)

DB-15 video connector

SATA DVD drive (optional)

12–17

Storage drive slots 0–5 (from bottom to top).

Slots 0 and 1 support only SAS drives (mechanical or SSD).

Slots 2–5 support both SAS and NVMe drives.

Server Back Panel Features

The following illustration shows the server back panel and describes its features.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды