Oracle X5-4 Скачать руководство пользователя страница 348

Страница: 348 / 358

AMI Checkpoint Ranges

Codes

Description

0xB4

■ USB hot plug.
■ Intel: STS_RNK_DETECT

0xB5

■ PCI bus hot plug.
■ Intel: STS_CHANNEL_EARLY

0xB6

■ Clean-up of NVRAM.
■ Intel: STS_JEDEC_INIT

0xB7

■ Configuration reset (reset of NVRAM settings).
■ Intel: STS_CHANNEL_TRAINING

0xB8 – 0xBF

Reserved for future AMI codes.

0x00B8

■ Reserved for future AMI code.
■ Intel: STS_INIT_THROTTLING

0x00B9

■ Reserved for future AMI code.
■ Intel: Memory BIST (Built In Self Test).

0x00BA

■ Reserved for future AMI code.
■ Intel Memory initialization.

0x00BB

■ Reserved for future AMI code.
■ Intel: DDR memory Map

0x00BC

■ Reserved for future AMI code.
■ Intel: RAS Configuration.

0x00BD

Reserved for future AMI code.

0x00BE

Reserved for future AMI code.

0x00BF

■ Reserved for future AMI code.
■ Intel: MRC done.

0xC0 – 0xCF

OEM BDS initialization codes.

DXE Error Codes

Codes

Description

0xD0

CPU initialization error.

0xD1

North Bridge initialization error.

0xD2

South Bridge initialization error.

0xD3

Some of the architectural protocols are not available.

0xD4

PCI resource allocation error. Out of resources.

0xD5

No space for legacy option ROM.

0xD6

No console output devices are found.

0xD7

No console input devices are found.

348

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды