Oracle X5-4 Скачать руководство пользователя страница 238

Страница: 238 / 358

Replace the Disk Drive Backplane (FRU)

Replace the Disk Drive Backplane (FRU)

This section provides instructions for replacing the disk drive backplane.

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

Prepare the server for service.

See

“Prepare the Server for Cold Service” on page 94

Remove and label all disk drives and fillers.

See

“Remove a Storage Drive (CRU)” on page 115

To ensure that the drives are returned to their slots, label the drives with their slot position.

Remove the DVD drive.

See

“Remove the DVD Drive or DVD Drive Filler Panel” on page 168

Disconnect the SAS/SATA cables and any NVMe cables (if present) from the disk

backplane.

See

“Replace the NVMe Switch Card Cables (FRU)” on page 215

and

“Replace the SAS 12

Gb/s Internal HBA SAS Cables (FRU)” on page 204

This will help provide the room needed to remove the disk backplane and its cables.

You do not need to remove the cables from the HBA or NVMe boards.

Disconnect the ESM cable from the ESM module.

See

“Replace the SAS 12 Gb/s Internal HBA ESM Cable (FRU)” on page 209

Or, simply remove the ESM module from its dual lock strip on the chassis.

Move the air divider.

238

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды