Oracle X5-4 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 358

background image

Servicing the DVD Drive (CRU)

Note -

If the system was ordered from the factory with optional NVMe drives, a PCIe NVMe

Switch card is installed in PCIe slot 1.

As a general rule, when installing a PCIe card in the server, use the following population order:

■

For a two-CPU configuration, the slot population order is: slot 6, 4, 5, 3, 1.
For example: When installing a PCIe card in a two-CPU configured server, first, determine

if slot 6 is available. If it is available, install the card in the slot. If it is not available,

determine if slot 4 is available. If slot 4 is not available, determine if slot 5 is available.

Continue this process with slots 3, and 1 until you find an available slot.

■

For a four-CPU configuration, the slot population order is: slot 11, 8, 6, 4, 10, 7, 5, 3, 9, 1
For example, when installing a PCIe card in a four-CPU configured server, first determine

if slot 11 is available. If it is available, install the card in the slot. If it is not available,

determine if slot 8 is available. If slot 8 is not available, determine if slot 6 is available.

Continue this process with slots 4, 10, 7, 5, 3, 9, and 1 until you find an available slot.

PCIe Cards With Boot Devices

If the server has several PCIe cards that provide boot devices, disable the Option ROM on the

PCIe slots not used for booting. By default, the BIOS enables Option ROMs for PCIe slot 2 and

the four on-board 10 Gigabit Ethernet ports.

Servicing the DVD Drive (CRU)

This section provides procedures for removing and installing the DVD drive and filler panel.

■

“Remove the DVD Drive or DVD Drive Filler Panel” on page 168

■

“Install the DVD Drive or DVD Drive Filler Panel” on page 170

Remove the DVD Drive or DVD Drive Filler Panel

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

168

Oracle Server X5-4 Service Manual • December 2015

«
...
166
167
168
169
170
...
»

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X5-4

Бренд: IBM Страницы: 438

Бренд: AIC Страницы: 112

R120d-1E N8100-1954F

Бренд: NEC Страницы: 166

FusionServer G8600 V7

Бренд: xFusion Digital Technologies Страницы: 112

Бренд: Hitachi Страницы: 58

Бренд: Hitachi Страницы: 192

Бренд: TRENDnet Страницы: 9

LAN Brick Eth 10

Бренд: MPI Technologies Страницы: 2

Titan SiliconServer

Бренд: Blue Arc Страницы: 487

Бренд: Atrust Страницы: 21

Бренд: ATON Страницы: 2

ABLELink SW2001

Бренд: Atop Страницы: 51

ABLELink GW21 MAXI Series

Бренд: Atop Страницы: 110

RF-ENCO-IP-HDSDI-35

Бренд: RFoG Страницы: 67

Бренд: Dell EMC Страницы: 108

PowerEdge R7525

Бренд: Dell EMC Страницы: 209

Print Server PocketBasic

Бренд: TROY Group Страницы: 30

Бренд: Gigabyte Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды