manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Oracle X5-4 - мощный сервер для вашего бизнеса. Получите начальное руководство по эксплуатации бесплатно, скачав его с manualshive.com. Этот manual поможет вам быстро начать использовать функционал сервера и сделать ваш бизнес еще более эффективным. Начните прямо сейчас!

Поделиться
Скачать
background image

Replace the Power Supply Backplane Board (FRU)

Note - 

The product serial number used for service entitlement and warranty coverage might

need to be reprogrammed by authorized service personnel with the correct product serial

number.

Replace the Power Supply Backplane Board (FRU)

This section provides instructions for replacing the power supply backplane board.

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Caution - 

Hazardous voltage. The system supplies power to the power board even when the

server is in standby power mode. Disconnect power cords before servicing the power supply

backplane board.

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

1.

Prepare the server for service.

See 

“Prepare the Server for Cold Service” on page 94

.

2.

Disconnect the SAS/SATA cables and the NVMe cables (if installed) from the disk

drive backplane and their PCIe card connections.

See 

“Replace the NVMe Switch Card Cables (FRU)” on page 215

 and 

“Replace the SAS 12

Gb/s Internal HBA SAS Cables (FRU)” on page 204

.

3.

Disconnect the ESM cable from the ESM module and its connection on the HBA.

See 

“Replace the SAS 12 Gb/s Internal HBA ESM Cable (FRU)” on page 209

.

4.

Remove all PCIe cards from the server, disconnecting any external or internal

cables and taking care to note their slot assignments.

226

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X5-4

Hanwha WRR-5301 Replacement Manual preview
WRR-5301
Бренд: Hanwha Страницы: 3
YOKOGAWA SMARTDAG+ GM10 User Manual preview
SMARTDAG+ GM10
Бренд: YOKOGAWA Страницы: 22
aizo digitalSTROM-Server Installation Notes preview
digitalSTROM-Server
Бренд: aizo Страницы: 2
Lantronix xPico XPW100A003-01-B Integration Manual preview
xPico XPW100A003-01-B
Бренд: Lantronix Страницы: 54
Axel AX3000/M85 Installation Manual preview
AX3000/M85
Бренд: Axel Страницы: 28
Supermicro SuperServer 5037C-i User Manual preview
SuperServer 5037C-i
Бренд: Supermicro Страницы: 88
AC&T System ETOS-100XP-E04 User Manual preview
ETOS-100XP-E04
Бренд: AC&T System Страницы: 32
Black Box PCA35A-R3 User Manual preview
PCA35A-R3
Бренд: Black Box Страницы: 30
Buffalo TERASTATION HS-D1.0TGL/R5 Technical Specifications preview
TERASTATION HS-D1.0TGL/R5
Бренд: Buffalo Страницы: 2
Acer Aspire EASYSTORE H341 Quick Start Manual preview
Aspire EASYSTORE H341
Бренд: Acer Страницы: 59
Acer Aspire EASYSTORE H341 Service Manual preview
Aspire EASYSTORE H341
Бренд: Acer Страницы: 74
Acer Aspire EasyStore Series User Manual preview
Aspire EasyStore Series
Бренд: Acer Страницы: 148
Acer Aspire easyStore H340 Service Manual preview
Aspire easyStore H340
Бренд: Acer Страницы: 68
Acer Altos EasyStore User Manual preview
Altos EasyStore
Бренд: Acer Страницы: 169
Acer Aspire easyStore H340 User Manual preview
Aspire easyStore H340
Бренд: Acer Страницы: 148
Acer Altos EasyStore Quick Installation Manual preview
Altos EasyStore
Бренд: Acer Страницы: 7
Dell PowerEdge 400SC Update preview
PowerEdge 400SC
Бренд: Dell Страницы: 1
Asus ASMB7-iKVM User Manual preview
ASMB7-iKVM
Бренд: Asus Страницы: 98

Бренды по названию

Популярные бренды

Загрузить еще бренды