Oracle X5-4 Скачать руководство пользователя страница 104

Страница: 104 / 358

Power Off, Remote (Oracle ILOM CLI)

Press and hold the Power button for at least five seconds until full power is off

and the server enters standby power mode.

Verify that the full power is off, and that the OK indicator on the front panel

blinks, indicating that the server is in standby power mode.

See Also

■

“Power Subsystem” on page 28

Power Off, Remote (Oracle ILOM CLI)

You can use the Oracle ILOM SP command-line interface (CLI) to remotely power off the

server to standby power mode.

Open an SSH session and log in to the Oracle ILOM CLI.

ssh root@

ipadress

where

ipadress

is the IP address of the server SP.

For more information, refer to the

Oracle X5 Series Servers Administration Guide

http://

www.oracle.com/goto/x86AdminDiag/docs

The Oracle ILOM CLI prompt appears:

104

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды