Oracle X5-4 Скачать руководство пользователя страница 251

Страница: 251 / 358

Replace the Motherboard (FRU)

10.

To remove the SAS, NVMe (if present), and ESM cables from the system,

carefully thread each one between the CPU 0 heatsink and the power supply side

wall, and out towards the front of the system.

Some of the cable connectors only fit one way between the CPU 0 heat sink and power supply

side wall as the space is very narrow.

11.

Remove the data and power cables for the disk backplane.

See

“Replace the Disk Drive Backplane (FRU)” on page 238

12.

Remove the power supply cable from the motherboard.

Connected to the motherboard from the power supply backplane.

13.

Remove any USB flash drives attached to the internal USB ports.

Make note of the ports for each USB flash drive.

14.

Remove the heatsinks and CPUs from the motherboard.

See

“Remove a Heatsink and CPU (FRU)” on page 186

15.

Remove the system battery.

See

“Replace the System Battery (CRU)” on page 172

16.

Loosen the green captive screw that secures the motherboard to the chassis.

Servicing FRU Components

251

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды