manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 146

Identify a Faulty DIMM

■

“Replace a Faulty DIMM” on page 143

■

“Replace a Faulty Memory Riser Card” on page 144

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

■

For memory riser card designation information, see 

“Component Designations” on page 73

.

■

For reference information, see 

“Memory Riser Card and DIMM Reference” on page 154

.

1.

Prepare for service.

See 

“Prepare the Server for Cold Service” on page 94

.

2.

To remove the MR card, pull the handles upward to disengage the connector

from the motherboard and carefully lift the memory riser straight up and out of

the server.

The MR card is designed to fit tightly into the MR connector on the motherboard. Th handles

on the MR card provide leverage against the chassis to disengage the card's edge connector

from the connector on the motherboard.

Next Steps

■

“Install a Memory Riser Card” on page 152

-or-

■

“Remove a DIMM” on page 148

-or-

■

“Install a DIMM” on page 150

-or-

■

“Replace the Motherboard (FRU)” on page 247

Identify a Faulty DIMM

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

146

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды