manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 345

AMI Checkpoint Ranges

Codes

Description

0xEB

S3 OS wake error.

0xEC - 0xEF

Reserved for future AMI error codes.

Recovery Progress Codes

Codes

Description

0xF0

Recovery condition triggered by firmware (Auto recovery).

0xF1

Recovery condition triggered by user (Forced recovery).

0xF2

Recovery process started.

0xF3

Recovery firmware image is found.

0xF4

Recovery firmware image is loaded.

0xF5 - 0xF7

Reserved for future AMI progress codes.

Recovery Error Codes

Codes

Description

0xF8

Recovery PPI is not available.

0xF9

Recovery capsule is not found.

0xFA

Invalid recovery capsule.

0xFB – 0xFF

Reserved for future AMI error codes.

PEI Beep Codes

Number of

Beeps

Description

1

Memory not Installed.

1

Memory was installed twice (InstallPeiMemory routine in PEI Core called twice).

2

Recovery started.

3

DXEIPL was not found.

3

DXE core firmware volume was not found.

4

Recovery failed.

4

S3 resume failed.

POST and Checkpoint Codes

345

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды