Oracle X5-4 Скачать руководство пользователя страница 259

Страница: 259 / 358

Returning the Server to Operation

This section provices procedures for how to return the server to operation after performing

service procedures.

Description

Link

Procedure to prepare the server for service.

“Prepare the Server for Operation” on page 259

Optional procedure to reinstall the server in

the rack.

“(Optional) Install the Server Into the Rack” on page 262

Optional procedure to reinstall CMA.

“(Optional) Install Cable Management Arm” on page 266

Procedure to check the installation of the

server in the rack.

“Verify Operation of Slide-Rails and CMA” on page 268

Procedure to reposition the server in the rack.

“Return the Server to the Normal Rack Position” on page 270

Procedure to power-on the server.

“Power On the Server” on page 271

Prepare the Server for Operation

Ensure that all components are completely installed.

Check for disconnected cables and unseated components and connect and install them correctly.

Place the cover on top of the server with the two latches at the front.

Ensure that the edges of the cover encapsulate the server sidewalls.

Lift the front edge of the cover and slide the cover away from the rear of the

server about 1 inch (2.54 cm).

This action ensures that the rear edge of the cover is positioned correctly.

Returning the Server to Operation

259

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды