manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Oracle X5-4 - мощный сервер для вашего бизнеса. Получите начальное руководство по эксплуатации бесплатно, скачав его с manualshive.com. Этот manual поможет вам быстро начать использовать функционал сервера и сделать ваш бизнес еще более эффективным. Начните прямо сейчас!

Поделиться
Скачать
background image

Install a Storage Drive Filler Panel (CRU)

4.

Close the latch to lock the drive in place.

5.

Do one of the following:

■

If you have replaced an NVMe drive using a hot-service procedure, refer to

the following for powering on the device:

■

“Removing and Replacing an NVMe Storage Drive Using Oracle

Solaris” on page 121

■

“Removing and Replacing an NVMe Storage Drive Using Oracle

Linux” on page 125

■

If you have replaced a storage drive using a cold-service procedure, power

on the server and configure the storage drive.

Use one of the power options described in 

“Power On the Server” on page 271

.

6.

Perform administrative tasks to reconfigure the drive.

The procedures that you perform at this point depend on how your data is configured. You

might need to partition the drive, create file systems, load data from backups, or have the drive

updated from a RAID configuration.

See Also

■

“Storage Drive Reference” on page 119

Install a Storage Drive Filler Panel (CRU)

For information about component filler panels, see 

“Component Filler Panels” on page 81

.

1.

Verify that the release lever on the storage drive filler panel is fully opened.

To open the lever, push the release button on the front of the filler panel.

2.

Slide the storage drive filler panel into the drive slot until it is fully seated.

3.

Close the latch to lock the filler panel in place.

See Also

■

“Storage Drive Reference” on page 119

Storage Drive Reference

This section shows the location and explains the functions of the storage drive status indicators.

Servicing CRU Components

119

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X5-4

SafeNet Luna SA Configuration Manual preview
Luna SA
Бренд: SafeNet Страницы: 109
IBM totalstorage 200 Service Manual preview
totalstorage 200
Бренд: IBM Страницы: 180
H3C UniServer R6900 G5 Installation, Quick Start preview
UniServer R6900 G5
Бренд: H3C Страницы: 17
Kathrein SAT-IP EXIP 418 User Manual preview
SAT-IP EXIP 418
Бренд: Kathrein Страницы: 16
Moxa Technologies NPort W2150Plus Series User Manual preview
NPort W2150Plus Series
Бренд: Moxa Technologies Страницы: 167
BlueNet Video BB01D User Manual preview
BB01D
Бренд: BlueNet Video Страницы: 38
xFusion Digital Technologies FusionServer G8600 V7 Manual preview
FusionServer G8600 V7
Бренд: xFusion Digital Technologies Страницы: 112
Blackberry ENTERPRISE SERVER FOR NOVELL GROUPWISE Installation And Configuration Manual preview
ENTERPRISE SERVER FOR NOVELL GROUPWISE
Бренд: Blackberry Страницы: 73
IBM 8678 Installation And User Manual preview
8678
Бренд: IBM Страницы: 96
Fujitsu Eternus DX80 S2 User Manual preview
Eternus DX80 S2
Бренд: Fujitsu Страницы: 186
Fujitsu ETERNUS DX60 User Manual preview
ETERNUS DX60
Бренд: Fujitsu Страницы: 242
Hitachi F1500 Hardware Manual preview
F1500
Бренд: Hitachi Страницы: 208
Hitachi AMS 2500 Getting Started Manual preview
AMS 2500
Бренд: Hitachi Страницы: 36
Excito B3 User Manual preview
B3
Бренд: Excito Страницы: 154
Viavi G4-PT-010-8T Hardware Installation preview
G4-PT-010-8T
Бренд: Viavi Страницы: 4
ORing Industrial Networking Corp. IDS-181A Quick Installation Manual preview
IDS-181A
Бренд: ORing Industrial Networking Corp. Страницы: 2
Meinberg LANTIME M100/GPS Technical Reference preview
LANTIME M100/GPS
Бренд: Meinberg Страницы: 38
Supero AS-4021M-32R User Manual preview
AS-4021M-32R
Бренд: Supero Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды