Oracle X5-4 Скачать руководство пользователя страница 37

Страница: 37 / 358

Troubleshooting and Diagnostics

This section describes troubleshooting information and provides procedures to help you

troubleshoot server hardware component faults.

Description

Link

Maintenance-related information and

procedures that you can use to troubleshoot

and repair server hardware issues.

“Troubleshooting Server Hardware Component

Faults” on page 37

Information about software and firmware

diagnostic tools that you can use to isolate

problems, monitor the server, and exercise

the server subsystems.

“Troubleshooting With Diagnostic Tools” on page 57

Information about attaching devices to the

server to perform troubleshooting.

“Attaching Devices to the Server” on page 59

Information on resetting the host or service

processor (including the Oracle ILOM root

password and account).

“Resetting the Host or Service Processor” on page 63

Information about contacting Oracle support.

“Getting Help” on page 66

Troubleshooting Server Hardware Component Faults

This section describes maintenance-related information and provides procedures that you can

use to troubleshoot and repair server hardware issues.

Description

Section Links

Troubleshooting overview information and

procedure.

“Troubleshooting Hardware Faults Using Oracle

ILOM” on page 38

Discerning the server state using the front

panel indicators.

“Troubleshooting Using the Front Panel Indicators” on page 40

Explanation of the system Fault Remind Test

Circuit.

“Troubleshooting Using the Fault Remind Test

Circuits” on page 51

Troubleshooting and Diagnostics

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды