Oracle X5-4 Скачать руководство пользователя страница 135

Страница: 135 / 358

Install a Fan Module

Ensure the cables are free from binding and pinching.

Slide the server into the rack until it locks into place.

If you performed a cold-service procedure, power on the server.

Fan Module Reference

The six fan modules are located at the front of the chassis and provide cooling for the three

motherboard cooling zones (for more information, see

“Cooling Subsystem” on page 25

). The

fans are hot-serviceable and accessible by partially extending the server from the rack. You do

not have to remove the server cover to service the fan modules.

Caution -

Server shutdown or component damage due to over-temperature condition. Fan

modules provide system cooling. If a fan module fails, replace it as soon as possible. When

you remove one of the fans in the back row, you must replace it within 30 seconds to prevent

overheating of the server.

Note -

If a failed fan is replaced too quickly, the fan indicator might still show a fault even after

the new fan is installed. When replacing a faulty fan, wait for the fan indicator to turn off after

removing the old fan and before installing the new fan. This will only take a few seconds.

The functions of the fan module status indicators is described below.

Front and Back Panel Indicators for Fan Failure

One or more of the following indicators might light when a fan module fault is detected:

■

Front and back Service Action Required indicators. See

“Server Front Panel

Features” on page 17

and

“Server Back Panel Features” on page 18

for locations of system

indicators.

■

Fan module Service Action Required indicator.

■

Over Temperature Warning indicator. This indicator might also light if a fan fault causes an

unacceptable increase in system operating temperature.

Fan Module Indicator

Next to each fan module slot are indicators that are visible from the top of the server.

Servicing CRU Components

135

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды