Oracle X5-4 Скачать руководство пользователя страница 230

Страница: 230 / 358

Replace the Power Supply Backplane Board (FRU)

The screw is located at the left front corner of the motherboard behind FM3.

16.

To unlock the motherboard, use the memory riser card guide by the processors

and the handle above the SP card slot to slide the motherboard toward the front

of the server.

This action unlocks the motherboard and plate assembly.

Note -

As you slide the motherboard forward, check that the Locator indicator light pipe

extension piece slides out of its hole in the chassis back wall.

17.

While gently sliding it away from the back of the server, carefully lift the front

end of the motherboard several inches.

230

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды