Oracle X5-4 Скачать руководство пользователя страница 228

Страница: 228 / 358

Replace the Power Supply Backplane Board (FRU)

Caution -

Hardware damage. Try not to allow the SAS and NVMe (if installed) cables to rub

against the CPU0 heatsink radiator fins. They are sharp and can damage the cable insulation.

Lift the air divider so the tabs clear the slots in the power supply side wall.

You might need to create cable slack where the SAS and NVMe (if installed) cables

route through from the PCIe area. Doing this enables the air divider to move more easily.

Carefully arrange the cables in the PCIe area to ensure they can move easily in the gap

between the power supply side wall and CPU0 without hanging on the CPU0 heatsink

radiator fins.

Move the air divider away from the side wall and gently rotate the divider

and the cables attached to it away from the backplane area and set it down

on the motherboard in the empty memory riser area.

10.

Disconnect the disk drive backplane power and data cables from the disk drive

backplane.

See

“Replace the Disk Drive Backplane (FRU)” on page 238

11.

Remove the ribbon cable connecting the power supply backplane to the

motherboard.

See the illustration in step 8.

12.

Remove the screw holding the power supply cover in place and remove the

power supply cover.

228

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды